This is an affiliates page which hopefully will pay for the maintenance of this website one way or another. Having personally tested the Dc-DC 10-32V to 12-35V mobile switcher it works very well – note though that the power supply does not have isolated (-) and (+) poles. The input (-) and output (-) are bonded together. Those wanting to do a little bit of DIY can wire wrap a separate secondary but I have not tested this – it is a work in progress.
We used two of these modules on a transformer with 0-12V 0-12V secondaries through two bridge rectifiers to get a split rail supply of +32 0 -32V rails. It is used to power two TDA7293 modules running at about 50W into 8 Ohms.
Parts-ring concentrates on the DIYer and in what better manner than playing around with some pretty cost effective boosting switcher supplies.
The company that sources and supplies these products also sells a 480W adjustable 48V supply. This makes these highly affordable SMPS a very good solution for those wanting to power their +/- 50V supply amplifier kits. We have not tested them yet but watch this space.
Input voltage: DC 10V-32V.
Output voltage: DC12V-35V(adjustable).
Output current: 10A (MAX).
Input current: 16A (MAX) (more than 10A please strengthen heatsink).
Output power: natural cooling 100W (MAX), strengthening cooling 150W (MAX) real power.
Conversion efficiency: 94% (when Output 19V 2.5A Input 16V, Reference).
Output ripple: 2% (MAX).
Working temperature: industrial (- 40 ° c to +85 °c) ( environmental temperature, more than 40 degrees, please reduce power to use, or – enhance cooling).
Full-Load temperature: 45 degrees.
No-load current: 25mA typical.
Voltage regulation: ± 0.5%.
Load regulation: ± 0.5%.
Dynamic response speed: 200uS 5%.
Short circuit protection: No (Please installs the fuse or protection circuit at input parts).
Input Reverse protection: No (please comply with a reverse protection or connect a diode at input parts.).
Dimension: 65mm x 35mm x 23.5mm.
DIY an adjustable on-board power supply, you just input DC 12V, then you can get output DC 12V-35V (adjustable), But the output voltage can not below the input voltage.
DIY a booster charger.
Provide power for your electronic equipment.
Use Solar battery charging for electric accumulator.
1 x Power Boost Module 150W Laptop Car
Module properties: non-isolated step-up module (BOOST)
Input voltage: DC 10V~60V
Input current: 10~30V input voltage, maximum current 30A
31~60V input voltage, maximum current 25A
Quiescent current: 15 mA (12V liter 20V, the output voltage, the higher the current will increase too quiet)
Output voltage: 12~90V continuously adjustable
Constant] range: 0.8~20A (±0.3A)
Temperature: -40~ + 85℃(ambient temperature is too high, please enhance heat dissipation)
Operating frequency: 150 KHz
Conversion efficiency: 92% ~ 97%
Low battery protection: yes
Input reverse polarity protection: yes
Enter the anti-reverse protection: yes
Short circuit protection: yes
Installation: 4 x 3 mm screw holes
Module size(L*W*H): 130 x 52 x 85 mm
1. DIY a power supply, 12V can input and output can 12-50V adjustable.
2. The power supply for your electronic device, according to your system can set the output
3. As the car power supply for your laptop, PDA or a variety of digital products supply.
4. DIY a mobile notebook power supply: 12V coupled with high-capacity lithium battery pack, so you can go where light where books.
5. Solar panel regulator.
6. To the battery, rechargeable lithium batteries.
1. Thickening of the radiator and intelligent temperature control cooling fan.
2. Have input MOS meter protection, don’t worry about input after burn out the power supply.
3. When used in battery input low battery protection avoid battery discharge damage power supply module and a battery.
1 x Boost Constant Current Module
200W 7A 6-35V To 6-55V High Power Step Up Boost Converter Charger Module With Aluminum Case ME3L
1, Input voltage: DC 6 – 35V2, The output voltage: DC 6 – 55V ( Note: This is a step-up board , only the output voltage is greater than or equal to the input voltage)3, Conversion efficiency: 97.6 percent ( input 32V output 45V / 3A when measured, the efficiency with input voltage and output voltage and current related)4, The maximum input power: 200W (30V when input voltage is greater than the maximum power)5, The maximum input current: 10A (Working long hours, please leave a certain margin)6, The maximum output current: 7A (long hours, please leave a certain margin)7, Module size: 70 x 39 x 32 mm (length x width x height) Package included:
1 x 200W Boost Converter
Short circuit overload, over voltage
on/off switch, or screws
Output Voltage:Adjustable 0-48V DC
Output Current: 10A
Frequency Range:47 ~ 63Hz
Cooling Fan Start Temperature:45 degrees
Over Heat Protection
The Working Environment:10 to 50 DEG C; 20% ~ 90%RH (no condensation)
Size: Approx 215*115*50mm
1 X Power Supply Driver